Specifications
Equipped With
GENERAL SPECIFICATIONS:
THE GEARS IN THE DRIVE REDUCTION BOX RUN IN A BATH OF OIL. A
THROUGH IS PROVIDED AT THE OUTSIDE OF THE OUTER TRACK TO CATCH
AND RETURN ANY OVERFLOW OF OIL. SIGH FEED GLASSES ARE PLACED IN
THE PRESSURE LINES TO PROVIDE A VISUAL CHECK ON THE FLOW OF OIL.
THE VARIOUS RETURN STREAMS DRAIN INTO THE DRIVE BOX AT REAR OF
THE BED AND THE OIL IS THEN RETURNED TO THE PUMP TANK.
LUBRICATION TO THE BARS IS PROVIDED BY A ONE SHOT SYSTEM LOCATED
ON THE SWINGS. A ONE SHOT LUBRICATING SYSTEM PROVIDES SUFFICIENT
OIL TO THE SLIDING BEARING WAYS OF THE SADDLES. THE FEED AND
TRAVERSE MECHANISM ON EACH END OF THE RAIL IS SUPPLIES WITH
LUBRICATING OIL BY A SMALL MOTOR DRIVEN PUMP ATTACHED TO THE FEED
AND TRAVERSE BOX.
PRINCIPAL CAPACITIES AND PRINCIPAL DIMENSIONS
MAXIMUM SWING 16'4"`
HEIGHT UNDER TOOL HOLDERS 6'0"
HEIGHT UNDER CROSSRAIL 7'0"
TABLE:
DIAMETER 12'0"
DEPTH OVER TRACKS 18"
OUTER TRACK OUTSIDE DIAMETER 76-1/2"
OUTER TRACK WIDTH 7"
INNER TRACK OUTSIDE DIAMETER 35"
INNER TRACK WIDTH 4-1/2"
CROSSRAIL HEADS:
BEARING WIDTH ON CROSSRAIL 34"
LENGTH OF BAR BEARING IN SWING 51-1/2"
BARS (OCTAGON TYPE):
TRAVEL 54"
DISTANCE ACROSS FLATS OF OCTAGON 8-3/8"
SWIVEL OF BAR EITHER SIDE OF VERTICAL 30 DEGREES
CROSSRAIL:
FACE WIDTH 31"
HOUSINGS:
FACE WIDTH 24"
BEARING LENGTH ON EXTENSIONS 98"
FEEDS:
FEEDS PER MINUTE .025" TO 1"
D.C. DRIVE:
HORSEPOWER OF DRIVE MOTOR 75
SPEED RANGE OF DRIVE MOTOR 850 TO 1700 RPM
BY FIELD CONTROL
850 TO 212 RPM
BY VARIABLE VOLTAGE
REVOLUTIONS PER MINUTE OF TABLE (APPROX) 1.5 TO 12
HORSEPOWER OF FEED AND TRAVERSE MOTORS (2) 3/5
SPEED RANGE OF FEED AND TRAVERSE MOTORS 450 TO 1800 RPM
BY FIELD CONTROL
450 TO 45 R.P.M
BY VARIABLE VOLTAGE
LUBRICATING PUMP MOTORS (3) 1/2 HP
GRINDING HEAD:
A VERTICAL GRINDING HEAD, SLIDABLY MOUNTED ON THE CROSSRAIL. IT
CONSISTS OF A SADDLE MOUNTED ON THE RAIL, THE FRONT FACE IS
PROVIDED WITH A VERTICAL SLIDE ON WHICH IS MOUNTED A POPE MODEL
P-2596 MOTOR DRIVEN GRINDING SPINDLE. NC GRINDING WHEEL IS
FURNISHED, BUT A WHEEL HOLDER AND A BALANCING BAR IS INCLUDED.
THE WHEEL HOLDER IS FOR A 12" DIAMETER WHEEL. THE SPINDLE IS
DRIVEN BY A 20 HP 1800 RPM, 220/440 VOLT, 3 PHASE, 60 CYCLE
MOTOR. NO CUTTING FLUID ATTACHMENT IS FURNISHED. THE GRINDING
HEAD IS PROVIDED WITH RAPID TRAVERSE ALONG THE RAIL, ALSO TO THE
VERTICAL SLIDE. HAND WHEEL FOR MANUAL ADJUSTMENT IN BOTH
DIRECTIONS IS ALSO PROVIDED. A ONE SHOT LUBRICATION SYSTEM,
PROVIDES OIL TO SLIDE WAYS OF SADDLE AND VERTICAL SLIDE. IT IS
NECESSARY TO LENGTHEN THE RAIL ON THE RIGHT SIDE TO PERMIT
PARKING OF EITHER THE BORING OR THE GRINDING HEAD.
EQUIPPED WITH:
3 AXIS DIGITAL READOUTS
WAS GOVERNMENT STANDBY MACHINE
PRICE ON LOCATION $145,000.00
